The following steps, you can easily charge on Brother printer cartridges. The different models have little variations in the other procedures remain unchanged.

Brother printer cartridge LC01C, LC01Y, LC01M and LC01BK (MFC 7000 series)

1 Set any absorbent material like a towel in place before refilling ink cartridges brother.

2 After filling ink in the bottle, remove the needle and syringe with the adapter cone shape about it.

3 Locate the hole in the cartridge, through which the river and take the exit port down to your lap.

4 Slowly inject the ink bottle from the syringe into the cartridge until the ink starts from the air hole and is not foamy.

5 Now turn the cartridge in the other direction, so that the ventilation hole in front of us and the outlet at the knees.

6 Insert the needle into the vial and syringe with the needle into the vent to inject. Next, inject the ink comes out of the exit hole and keeps foaming.

7 Leave the cartridge in this position for ten minutes. Then repeat step 6 and let sit for ten minutes.

8 Install the cartridge into the printer. If it has to be transported, then tape the socket can lid and air vents, but must be removed before printing
.
Brother printer cartridges for Brother MFC-7150 and MFC-br <-7160 />
It is a sponge in the cartridge that makes the sticky filling. The first step remains the same.

1 Locate the exit hole at the base, where there is a great stop.

2 The vent found on the ground that are on the same side as the major treat to the top of the cartridge.

3 From the starting position of the vent on the right knee and vice versa. Close the socket with a black electrical tape.

4 Pull the handle on top of the cartridge. Inside you will find two metal seals, and the first round and the largest square. Remove the seals or holes in them.

5 inserted to fill the squeeze bottle of ink-filled syringe with the bottle and the needle of the syringe into the bottle of ink. Relax your grip and let the syringe to suck the ink in the bottle.

6 Under the syringe bottle slowly, the ink in the sponge in the deep rectangular hole, until the sponge saturated fatty acids.

7 The ink in the round hole to the outer chamber is full. After injection, seal the round hole with black electrical tape carefully. Also seal the rectangular hole with tape.

8 Place the plastic handle on top again. Remove the cartridge, a sink and remove the lower band. Let the ink is flowing.

9 Printer should now be installed.

Brother printer cartridge LC41C, LC41Y, LC41M and LC41BK

In this model remains the ink because of the valve. The first step is the same.

1 Find the label marked with letters like LC41 C, M, Y or BK for color.

2 Under the label side up, on the right is a window to the top of the cartridge. Make a hole in the window with a smoldering iron or something hot metal.

3 Fill the syringe bottle as in step 5 above.

4 Inject the ink slowly bottle with the syringe in the window in the upper right corner of the cartridge. Fill the entire cartridge.

5 Close the window with black electrical tape.

6 Install the printer on.

HJ100 Brother printer cartridge and

HJ400 There is much difference in this cartridge. The first step remains the same.

1 Start with a bolt in the vent opening, opposite the longest side of the cartridge which is opposite the print head.

2 Mark the connector with screw. Fill the syringe with half a bottle of ink and put it in the hole. Inject slowly and deeply into the sponge.

3 Expected to fall. Tape you have to experience.

toner filling a toner cartridge laser is very similar to adding gasoline slurry or gas for your car. The toner cartridge must be in a place where no wind. It can work burn, where there is no flame. Also, do not breathe as it is irritating

The three main types of laser toner cartridges are as follows:.

O sleigh: a tube for holding toner

o Drum with gears and a drum, a gelatin layer

o toner and developer: similar drum cartridge But with the toner and developer two

slide.

first cartridge Spread some absorbent material like a towel or newspaper. Search for a card at the end of the cartridge.

2 Remove the cap, if you find it. If you do not, then create a hole that is far from the paper (smooth plastic surface).

3 If you create a hole then carefully remove the chips. 4. Shake the bottle of toner and pour the whole bottle into the cartridge with a funnel or paper funnel.

5 Replace the cap and seal with black electrical tape.

6 Install the printer on. The filling of these cartridges can be done many times.

Drum Cartridge These cartridges are much more complex. The ‘pretty’ drum three color channels are red, blue or green. Before you fill find the toner hopper and waste hopper.

O Locate the drum and place it rises towards the end of the cartridge.

O lay there, until the drum rotates from left to right before you leave. The page you are is the “closest and far from you is” beyond.



. Waste hopper ‘o The largest site is “toner hopper and carry the smaller

now to the following steps.

1 Locate the drum but not touch. It may be in a flap be.

2 Find the toner cartridge. you will see a translucent plug on one side. Remove it. If you can not find then a hole in the toner hopper away from the paper path.

3 empty drum chips, but do not touch the drum.

4 Shake the bottle of toner and pour the whole bottle into the cartridge with a funnel.
5.Seal the hole with the pug or a black electrical tape.

Toner & Developer

This cartridge is very similar to the drum unit, but it has two ports . The largest toner and the other for developers. You will need medium sized flat and Phillips screwdrivers.

1 Find the waste removed in the box at the end of the cartridge and the screws. There is a sliding door one in the trash.

2 Behind the litter box, a plastic plate with a single screw is held. You have to be organized so that the Green Party to the right top and screw down. Screw it open.

3 This is a clip on the green side. Insert a screwdriver to release the plate.

see 4 to be large cap the toner. Get the cap or a hole in it.

5 Fill in the sixth seal cartridge.

against the center-left is a small plug for the developer. Make a hole or separate.

7 Fill the hole with the developer and the seal.

8 Place the plastic box and litter.

9 Shake the cartridge gently.


Toner cartridges